|
Porta-Nailer 461 1-inch 18 Gauge Narrow (1/4") Crown Flooring Stapler | 
 enlarge | Brand: Porta-Nails
Category: Home Improvement
List Price: $294.47
Buy New: $199.00
You Save: $95.47 (32%)
New (5) from $199.00
Rating:  24 reviews
Sales Rank: 892
Media: Tools & Hardware
Shipping Weight (lbs): 5.5
Dimensions (in): 13.4 x 10.3 x 2.8
MPN: 461
Model: 461
UPC: 726205046116
EAN: 0726205004611
ASIN: B0000VXQ3M
Shipping: Eligible for Super Saver Shipping
Promotion: Save $10.00 when you spend $50.00 or more on Qualifying Items offered by Amazon.com. Enter code BMLSAVES at checkout. Terms and Conditions
Availability: Usually ships in 24 hours
| |
| Features:
| • | Versatile hardwood flooring tongue and groove stapler | | • | Includes flooring shoe and conventional nose | | • | Precise – drives staples at 45 degree angle every time | | • | Lightweight, easy to handle | | • | 1/4" crown 1" 18 gauge galvanized staples |
|
| Accessories:
|
| Similar Items:
|
| Editorial Reviews:
Product Description
3/8" & 1/2" Wood/Laminate Flooring; Versatile hardwood flooring tongue and groove stapler; Precise - drives staples at 45 degree angle every time; Lightweight, easy to handle; 1/4" crown 1" 18 gauge galvanized staples; Converts to a conventional underlayment stapler (nose included); Includes carrying case
|
| Customer Reviews: Read 19 more reviews...
 bjm November 13, 2008
Brian J. Mate (Central Georgia)
Good product. It did what it was suppose to. No problems with jams.
Worked like a charm. September 8, 2008
J. Goff (Central Ca.)
1 out of 1 found this review helpful
Knowing that I had a flooring job that was going to take place over multiple weekends, It made more sense cost-wise to just outright by a flooring stapler. After a little online research, I chose the 461 for a couple of reasons. One, was the fact that it could easily be converted to a standard stapler (something few models do). Also, the price point was reasonable.
After finishing the first 200 sq ft. of the project this weekend, I can honestly say that the 461 worked like a champ. After dialing the pressure into 70 PSI, the 461 sailed through the Bruce Engineered hardwood flooring in my kids bedroom. I never had one dry fire, twisted staple, blowout or any other issues whatsoever.
Overall, I'm extremely satisfied with the nailer. My one complaint may be the lousy directions (which don't even specify how to convert the nailer from standard configuration to floor stapler). Aside from that, I'm very happy with its performance.
 Porta-Nailer 461 August 25, 2008
R. W. Schumacher (Wisconsin)
1 out of 1 found this review helpful
All in all, I'm happy with the Porta-Nailer 461. I just finished 550 square feet of Bamboo flooring for which I used 3000 staples. I didn't have a single staple jam even when I mistakenly put one staple right on top of another.
One of the appealing features of the 461 is that it takes a 1.25 inch staple. Most 18 gauge staplers won't take anything longer than an inch. The extra length is important for 1/2 inch flooring. (The printed material that came with the stapler only talked about using one inch staples, but the sticker on the stapler itself said that it takes up to 1 1/4 inch staples.)
The instructions were a little weak in other areas also. Though they are very thorough in describing the safety features and how to use the stapler safely, they didn't explain how to install the flooring foot. However, it only took me about a minute to figure it out and get it together. The instructions describing how to load the staples apparently described a different, perhaps older, model. But it was easy enough to figure out how to load the staples, even though the system is a bit different from the average stapler.
The flooring foot is a bit small, so it takes a little concentration to make sure it is seated correctly on the tongue of the board. That may slow down the work a bit at first until you get a good feel for the process. (I'm not sure the foot of any other 18 gauge stapler is any better.)
Also, the stapler sometimes bent the top of the staple over. Never really figured out why that was happening. It may have been a result of me not having the stapler perfectly seated on the tongue (see the note above about the small flooring foot.) Or it may have been the result of quality of the staples. Or it may have had something to do with the hardness of the boards and grain patterns in the boards. Because I was nailing 1/2 solid hardwood, I suspect any stapler might have trouble with an 18 gauge staple. That is a pretty light gauge to go through through a hard wood.
It wasn't a huge issue. For those staples, I just had to have a nail set handy to tap the staple top down into the tongue so the next board would fit tight. I can imagine, however, that a flooring contractor might have been a bit peeved at having to take the time to do that.
My review may sound a bit negative, but I really was satisfied with the machine. The stapler itself seems to be solid and well built. And it got the job done without damaging the wood. I can recommend the tool.
floor stapler August 18, 2008
Gary T. Haight
1 out of 1 found this review helpful
This is one of the best tools I have ever owned. I put in about 400 sq ft of 3/8 " hardwood flooring without a hitch. Not one jamb!! Ran pressure about 70psi and it worked great. I would highly recommend
lay floors fast July 30, 2008
Wesley Ng (Austin, TX)
1 out of 1 found this review helpful
Before buying this floor stapler, we were using a manual stapler for hard wood floors. This made the job must easier and more pleasant. The Porta-Nailer is well built and comes with a carrying case and an interchangeable piece to turn the stapler into a point and shoot stapler.
Note that this stapler is only useful for thinner engineered wood floors.
|
|
|
Copyright 2008 | |
